单冷净化送风柜的保养与维修指南 Maintenance and Repair Guide for SingleCooling Purification Air Supply Cabinets

1. 日常保养 (Daily Maintenance)  
1. 清洁过滤器 (Clean Filters):  
    定期检查并清洁初效和中效过滤器，确保无堵塞。  
     Regularly inspect and clean the primary and mediumefficiency filters to ensure no blockage.  
    根据使用频率，建议每13个月更换一次过滤器。  
     Replace filters every13 months depending on usage frequency.

2. 检查风机运行状态 (Check Fan Operation):  
    监听风机运行声音，确保无异常噪音。  
     Listen for abnormal noises during fan operation.  
    检查风机轴承润滑情况，必要时添加润滑油。  
     Check the lubrication of fan bearings and add lubricant if necessary.

3. 清洁送风口 (Clean Air Outlets):  
    定期清理送风口，防止灰尘堆积影响送风效果。  
     Regularly clean air outlets to prevent dust accumulation that may affect air supply efficiency.

4. 检查电气连接 (Inspect Electrical Connections):  
    检查电源线、接线端子是否松动或老化，确保电气安全。  
     Inspect power cords and terminals for looseness or aging to ensure electrical safety.

2. 定期维护 (Regular Maintenance)  
1. 清洗蒸发器 (Clean Evaporator):  
    每6个月清洗一次蒸发器，防止灰尘和污垢影响冷却效果。  
     Clean the evaporator every 6 months to prevent dust and dirt from affecting cooling efficiency.

2. 检查冷凝水排水系统 (Check Condensate Drainage System):  
    确保排水管道畅通，避免冷凝水积聚导致设备损坏。  
     Ensure drainage pipes are clear to prevent condensate accumulation and equipment damage.

3. 校准温湿度传感器 (Calibrate Temperature and Humidity Sensors):  
    每12个月校准一次传感器，确保数据准确。  
     Calibrate sensors every12 months to ensure accurate data.

4. 检查电气控制系统 (Inspect Electrical Control System):  
    检查控制面板、继电器和接触器的工作状态，及时更换损坏部件。  
     Inspect the control panel, relays, and contactors, and replace damaged components promptly.

3. 故障排除与维修 (Troubleshooting and Repair)  
1. 送风量不足 (Insufficient Air Supply):  
    检查过滤器是否堵塞，清洁或更换过滤器。  
     Check if filters are clogged, clean or replace them.  
    检查风机是否正常运行，必要时维修或更换风机。  
     Check if the fan is operating normally, repair or replace if necessary.

2. 冷却效果差 (Poor Cooling Performance):  
    检查蒸发器是否脏污，进行清洗。  
     Check if the evaporator is dirty and clean it.  
    检查制冷剂是否充足，必要时补充制冷剂。  
     Check refrigerant levels and replenish if necessary.

3. 设备噪音过大 (Excessive Noise):  
    检查风机轴承是否磨损，更换轴承。  
     Check if fan bearings are worn and replace them.  
    检查涂装设备安装是否稳固，加固安装支架。  
     Check if the equipment is securely installed and reinforce the mounting brackets.

4. 电气故障 (Electrical Faults):  
    检查电源电压是否稳定，确保符合设备要求。  
     Check if the power supply voltage is stable and meets equipment requirements.  
    检查控制电路是否正常，修复或更换故障部件。  
     Inspect the control circuit and repair or replace faulty components.

4. 安全注意事项 (Safety Precautions)  
1. 断电操作 (Power Off Before Maintenance):  
    在进行任何维护或维修前，务必断开电源。  
     Always disconnect power before performing any maintenance or repairs.

2. 佩戴防护装备 (Wear Protective Gear):  
    清洁或维修时，佩戴手套、口罩和护目镜。  
     Wear gloves, masks, and goggles during cleaning or repairs.

3. 专业维修 (Professional Repair):  
    对于复杂故障，建议联系专业技术人员处理。  
     For complex faults, it is recommended to contact professional technicians.

通过以上保养与维修措施，可以确保单冷净化送风柜的高效运行，延长设备使用寿命，并保障涂装生产线的稳定生产。  
By following the above maintenance and repair measures, the efficient operation of the singlecooling purification air supply cabinet can be ensured, extending the equipment's service life and guaranteeing stable production in the painting line.

注：以上内容来自于网络整理，仅供参考，请按实际维护保养手册为准！